How To Change Battery On Samsung S6

Introduction

Employ this guide to supersede the battery in your Samsung Galaxy S6.

Before disassembling your telephone, discharge the battery below 25%. A charged lithium-ion bombardment can catch fire and/or explode if accidentally punctured.

If your bombardment is bloated, take appropriate precautions. Practise not rut your telephone. If needed, y'all can use a dropper or syringe to inject isopropyl alcohol (90+%) around the edges of the back cover to weaken the agglutinative. Bloated batteries can exist very dangerous, so vesture eye protection and exercise due caution, or take it to a professional if you're not sure how to continue.

This guide involves removing the rear glass. Removing the rear glass destroys the adhesive holding it in place. Follow this guide to reinstall the rear drinking glass.

Insert a paper clip or SIM eject tool into the hole in the SIM card slot on the power button side of the phone.

Insert a paper prune or SIM eject tool into the pigsty in the SIM card slot on the power button side of the telephone.
Press to eject the SIM menu tray.
Don't printing too hard or you may impairment the SIM card tray.

Remove the SIM card tray from the phone.

Remove the SIM card tray from the telephone.

We recommend that y'all clean your microwave before proceeding, as any nasty gunk on the lesser may end upwards stuck to the iOpener.
Identify the iOpener in the center of the microwave.
For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn down.

Heat the iOpener for thirty seconds.
Throughout the repair process, equally the iOpener cools, reheat it in the microwave for an boosted thirty seconds at a fourth dimension.
Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.
Never touch the iOpener if it appears swollen.
If the iOpener is still likewise hot in the middle to touch, go along using it while waiting for it to cool downward some more than before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

Remove the iOpener from the microwave, property it by one of the two flat ends to avert the hot center.
The iOpener will be very hot, so be conscientious when treatment it. Use an oven paw if necessary.

If you don't have a microwave, follow this step to heat your iOpener in humid water.
Make full a pot or pan with plenty water to fully submerge an iOpener.
Rut the water to a boil. Turn off the estrus.
Identify an iOpener into the hot water for two-3 minutes. Make sure the iOpener is fully submerged in the water.
Use tongs to extract the heated iOpener from the hot water.
Thoroughly dry the iOpener with a towel.
The iOpener will be very hot, so be careful to hold information technology only by the end tabs.
Your iOpener is ready for use! If y'all need to reheat the iOpener, oestrus the water to a boil, turn off the heat, and place the iOpener in the h2o for 2-3 minutes.

Opening your telephone will compromise its waterproof seals. Accept replacement agglutinative set earlier y'all proceed, or take care to avoid liquid exposure if y'all reassemble your phone without replacing the adhesive.
If your glass is shattered, put packing tape over the entire panel to agree information technology together during the removal procedure.
Lay the heated iOpener over the rear panel for about two minutes to loosen the agglutinative effectually the edge of the glass.
You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.
Shift the iOpener to heat the remaining section of the panel for another 2 minutes.
A hair dryer, heat gun, or hot plate may too be used, only exist conscientious non to overheat the phone—the OLED brandish and internal bombardment are both susceptible to heat damage.

Once the rear drinking glass is hot to the touch on, utilize a suction cup nigh the bottom edge of the glass.
Lift on the suction loving cup to create a minor gap underneath the rear drinking glass, and insert an opening pick into the gap.
Optionally, once the selection is inserted, yous can add together a few drops of isopropyl alcohol into the gap to help weaken the adhesive in the post-obit steps.

Slide the choice forth the lesser border of the phone to slice through the adhesive securing the rear glass.
Afterward, it may help to leave the choice in identify and grab a second pick as you proceed to the adjacent step. Leaving the pick inserted can assistance prevent the glue yous just separated from re-adhering.
Re-heat the rear drinking glass as needed to preclude the gum from cooling and hardening.

Echo the heating and cutting process for the remaining three sides of the phone.
Leave an opening option under each edge to foreclose the adhesive from resealing.

Use an opening pick to slice through whatsoever remaining adhesive.
Remove the rear glass.

To install new rear glass:
Use tweezers to peel away any remaining adhesive from the telephone'south chassis.
Make clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-gratis cloth. Swipe in one direction only, non back and forth. This will aid prep the surface for the new adhesive.
Peel the agglutinative backing off of the new rear glass, carefully line up one edge of the drinking glass against the phone chassis, and firmly printing the drinking glass onto the phone.
If you're reinstalling the onetime rear glass, or using rear glass without adhesive pre-installed, follow this guide.

Remove the thirteen iii.5mm Phillips #00 screws securing the midframe to the phone.

Before you perform this step, make certain you've ejected the SIM card tray.
Firmly grasp the border of the midframe assembly.
Lift up on the midframe assembly while pushing down on the bombardment to divide the midframe assembly from the balance of the phone.
While lifting the midframe, exist careful to avoid snagging it on the audio jack or charging port.
Once the midframe is partially seperated, carefully run an opening pick around the edges of the rest of the phone to carve up the top of the midframe.
Be careful not to accidentally insert the opening option between the drinking glass and display.
To avoid damage to the headphone jack, remove the top of the midframe first, then push the midframe downwardly to disengage it from the headphone jack.
Yous may need to heat and employ an iOpener to the edges of the brandish to soften the display adhesive if midframe separation is difficult.

Lift the midframe assembly upwards to divide it from the rest of the phone.

Utilize the flat end of the spudger to disconnect the battery connector from its socket on the motherboard.

Insert a plastic opening pick between the case and the battery.
Exist conscientious to keep the pick as flat as possible to avoid bending the bombardment, which may harm it and cause it to release unsafe chemicals.
Push the option further in to split the battery from the phone.
If the battery is too strongly adhered for the opening pick, place a warm iOpener over the battery to loosen the adhesive.
Alternatively, employ some isopropyl alcohol under each corner of the battery and allow it to penetrate for several minutes to help weaken the adhesive.
Exercise not pry against the motherboard or you may damage the telephone.

Remove the battery from the telephone.
Practise not reuse the battery later on it has been removed, as doing so is a potential safety run a risk. Replace it with a new battery.
Follow these instructions to install a new battery and adhesive.